{"id":75,"date":"2015-10-29T22:56:14","date_gmt":"2015-10-29T22:56:14","guid":{"rendered":"https:\/\/zhutarduino.wordpress.com\/?page_id=75"},"modified":"2020-10-12T16:20:33","modified_gmt":"2020-10-12T16:20:33","slug":"arduino-sound-activated-flash-or-camera-trigger","status":"publish","type":"page","link":"https:\/\/thezhut.com\/?page_id=75","title":{"rendered":"ARDUINO sound activated flash or camera trigger"},"content":{"rendered":"

\"FT489G3IFCDF1HR_MEDIUM\"<\/a><\/p>\n

 <\/p>\n

This\u00a0tutorial will show you how to build a simple circuit to connect to a ARDUINO<\/span><\/a> micro controller that will detect sound and trigger your camera or flash for high speed photography. This is easy to assemble and only cost a few $$$ for the parts…<\/p>\n

\u00a0<\/a><\/p>\n

\"flash_triger_schem\"<\/a><\/p>\n

 <\/p>\n

The picture above is the schematic for the circuit you will need to build… if you click on\u00a0the picture\u00a0it will enlarge so you can see it better….<\/p>\n

The parts you will need:<\/strong><\/p>\n

#affiliate links#<\/p>\n

220\u03a9 resistor X 1<\/span><\/a><\/p>\n

10K\u03a9 resistor X 2<\/span><\/a><\/p>\n

100K\u03a9 resistor X 1<\/span><\/a><\/p>\n

1M\u03a9 resistor X 1<\/span><\/a><\/p>\n

0.1\u00b5f capacitor X 2<\/span><\/a><\/p>\n

1N4001 (or allmost any diode will work) X 1<\/span><\/a><\/p>\n

MPS2222A ( or any similar transistor like 2N2222 will work) X 1<\/span><\/a><\/p>\n

optocoupler ( any 4 pin type should work, I used a Sharp PC817) X 1<\/span><\/a><\/p>\n

Microphone X 1<\/span><\/a><\/p>\n

any ARDUINO board X 1<\/span><\/a><\/p>\n

 <\/p>\n

 <\/p>\n

\"FLKVDNRIFDSVIQ6_MEDIUM\"<\/a><\/p>\n

 <\/p>\n

copy and paste the following code into your ARDUINO IDE…<\/p>\n

int flash = 9;\u00a0\u00a0 \/\/flash or camera trigger pin
\nint mic;
\nint lvl = 0;
\nint trig;
\nvoid setup() {
\npinMode(flash, OUTPUT);
\nSerial.begin(9600);
\n}
\nvoid loop() {
\nif (lvl == 0)
\n{
\nSerial.println(“What Sound Trigger LVL do you want? “);
\nlvl = 9000;\u00a0 \u00a0\/\/sets trigger lvl high so it wont trigger till you enter a value
\n}
\nif (Serial.available())
\n{
\nlvl = Serial.parseInt();
\nlvl = constrain(lvl, 25, 9000);\u00a0\u00a0 \/\/stops you from setting sound detection lvl to low and cause continuous
\nSerial.print(“Sound Trigger LVL is “);\u00a0\u00a0 \/\/triggering, you can change the 25 to a lower # but don’t go under 15
\nSerial.println(lvl);
\nSerial.println(“What Sound Trigger LVL do you want? “);
\ntrig = 0;
\n}
\nmic = analogRead(A0);
\nif (mic >= lvl)
\n{
\ndigitalWrite(flash, HIGH);
\ndelay(1);
\ndigitalWrite(flash, LOW);
\ntrig = trig + 1;
\nSerial.print(“Flash has been Triggered “);
\nSerial.print(trig);
\nSerial.println(” Times!”);
\ndelay(1000);\u00a0\u00a0 \/\/delay so your camera or flash only triggers one time from a sound
\n}
\n}<\/p>\n

——————————————————————————————————————-<\/p>\n

After you get the code loaded onto the arduino power it up then plug it into your flash or camera. It wont hurt the camera or flash to have it connected when you power up the arduino but it will trigger it one or two times when its first starting up…<\/p>\n

Next open up your serial monitor, you can use the one on your computer or if you have a android smart phone & a USB OTG cable<\/span><\/a> you can down load a free serial monitor from the play store<\/span><\/a>.. Just follow the instructions on the serial monitor and your good to go, if you have any problems or questions\u00a0leave a comment on our Facebook Page and ill try to help you out…<\/p>\n

 <\/p>\n","protected":false},"excerpt":{"rendered":"

  This\u00a0tutorial will show you how to build a simple circuit to connect to a ARDUINO micro controller that will detect sound and trigger your camera or flash for high speed photography. This is easy to assemble and only cost … Continue reading →<\/span><\/a><\/p>\n","protected":false},"author":2,"featured_media":0,"parent":10,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"footnotes":"","_links_to":"","_links_to_target":""},"class_list":["post-75","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/thezhut.com\/index.php?rest_route=\/wp\/v2\/pages\/75","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/thezhut.com\/index.php?rest_route=\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/thezhut.com\/index.php?rest_route=\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/thezhut.com\/index.php?rest_route=\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/thezhut.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=75"}],"version-history":[{"count":1,"href":"https:\/\/thezhut.com\/index.php?rest_route=\/wp\/v2\/pages\/75\/revisions"}],"predecessor-version":[{"id":1585,"href":"https:\/\/thezhut.com\/index.php?rest_route=\/wp\/v2\/pages\/75\/revisions\/1585"}],"up":[{"embeddable":true,"href":"https:\/\/thezhut.com\/index.php?rest_route=\/wp\/v2\/pages\/10"}],"wp:attachment":[{"href":"https:\/\/thezhut.com\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=75"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}